HOME PAGE



©1998 Reckart Equipment Co.
Site design by Citynet

  • Reckart R642 hd
    Includes 10' infeed with 4 - 6' table rolls, with 1-7/16" shaft and bearings. The table is constructed of 6" channel frame with legs, with one adjustable tube type guide fence 0"-6". The main frame is made of 5/8" flat steel with 2-15/16" mandrel with outboard bearing on adjustable bearing base. Unit with (4) 6-1/2" inserted tooth feed rolls with 1-11/16" shaft and bearings that are driven by #80 roller chain with (2) 5 HP motors through speed reducers. Unit wired for three phase, 460 volt with reversing starter on slow side, controls for slow, fast, stop and reverse. Unit has (2) 8-1/2" diameter pressure rolls with air lift cylinder and down pressure. Unit has one stationary saw collar and two ball bearing saw collars with movable saws moving with hand wheel in unison, with anti-kickback fingers and guards for top of edger and overdrive unit, unit with bottom safety fingers. Unit LESS: Rear table, main motor and drive Unit accepts 21" saws.

    Options:
    • Air lift safety fingers
    • Two saws moving independently in place of in unison
    • Tube type adjustable guide fence 0"-6"
    • Stationary guide fence
    • 10' rear table with 3-6" rolls, 1-7/16" bearings
    • 10' outfeed table with 3-6" live rolls driven from edger
    • 5" X 20' belt tailer driven from edger
    • 14" X 20' belt tailer driven from edger
    • 42" X 20' belt tailer driven from edger
    • 5 HP independent drive for belt tailer
    • 21" carbide tipped saws, each
    • 20" inserted tooth saws, each
    • Stationary saw collar, starting and finishing collar, bolts, one collar for two saws
    • Each additional center collar under 2-1/8"
    • Each additional center collar between 1-1/2"-4"
    • Hydraulic power shift, including hydraulic tank, pump, motor and control valve for two saws moving in unison
    • Cant holdover mounted in infeed table with air cylinder and control valve
    • Cant holdover powered from hydraulic power pack
    • Powered rear pressure rolls
    • Complete moveable saw collar
    • U joint for moveable saw
    • 6" X 6" roll for cant holdover 1-15/16" bore
    • EXTRA for 48" wide machine in place of 42"
    • EXTRA for 48" wide machine with 3-7/16" mandrel and bearings and 1" side plates in place of standard
    • EXTRA for spray mist unit with manual valve for mandrel and 1-1/4" slide shaft
    • EXTRA for 7-1/2 HP motor and larger tank on hydraulic system, hydraulic motors installed on each 1-1/4" shaft that turns only when saws are being shifted
    • EXTRA for overhead motor mount and guard
    DIMENSIONS (Edger Frame)
    • Base Length 64-1/2"
    • Base Width 72"
    • Infeed Table 10'0"
    • Outfeed Table 10'0"
    GENERAL CONSTRUCTION
    • Side Plate "Frame" 5/8" Plate Steel
    • Arbor 2-15/16" T.G.P
    • Feed Rolls 6-1/2" Inserted Tooth
    • Press Rolls 8-1/2" diameter
    • Saw Collars Ball Bearing
    PERFORMANCE
    • Max. Depth of Cut 6-1/2"
    • Max. Width of Material 42", less saw setting
    • Feed Rate (Edger side) 135 L.F.P.M
    • Feed Rate (Cant side) 55 L.F.P.M
    • Mandrel Speed 1770 RPM
    • Arbor Size 2-15/16"
    • Power Required: Main drive motor 30-200 HP (Not included) Feed roll drive motor 2-5 HP
    R436    R642    R848    R848TA




    [ reckart edgers ] [ sawmill design ] [ custom fabrication ]
    [ logging equipment ] [ parts & supplies ] [ information request ]
    [ sawdust blowers ] [ links ] [ contact us ]